dumbguy
| reply to rcilink
Re: [PAP2] Unlocking Guide
can anybody explain the step4:Browse to the web page of the PAP2.
I know my Linksys router IP is 192.168.1.1 and my TFTP svr ip is 192.168.1.100. Thanks. |
|
ropeguru
Premium
join:2001-01-25
Bridgeport, WV
clubs: | in your web browser, such as internet explorer, put »192.168.1.1 in the address line.
--
FWD#: 223611 |
|
O_R
| reply to rcilink
wowww thank you Matt, Rcilink & DaSneaky1D !!!!!
it worked on the PAP2 I got from Staples (NY).
Admin w/o password! 
now lets see If I can configure stanaphone with it.
If others need help, post details, I will try to help, but this step-by-step guide worked with TFTP (solarwinds.net) flawlessly on 2.0.12(LS) original firmware.
Regards,
O |
|
all4jo
Hoser
Premium
join:2002-02-10
Haiti | reply to rcilink
hey guys , what network can i use a unlocked pap2? im new to this .
thanks
Jose |
|
hardly
join:2004-02-10
USA | reply to mazilo
Once unlocked, can you flash with Linksys PAP-2NA firmware?
If so, can you then perform a Factory Reset without worrying about it reverting to Vonage defaults?
Thanks |
|
rizzo2dial
Premium
join:2004-08-05
| The PAP2 and PAP2-NA use identical firmware. The PAP2 has different NVRAM values burned into the device than the PAP2-NA which is why a Master Reset reverts the device back to a locked Vonage adapter.
I tried numerous combinations of trying to reset the adapter (both while in "Sipura" mode and "Linksys" mode, switching back 'n forth between the firmware flavors).
It "Sipura" mode, a master reset acted like all "default Sipura" settings were loaded; however, once switching back to "Linksys" firmware, it was a locked PAP2 Vonage adapter again.
Rizzo |
|
illek
Premium
join:2005-03-23
Tulsa, OK | reply to rcilink
OK, just cleaned out the Staples stores in Tulsa. Unfortunately, only 6 were left. Will try it tomorrow and report back any problems.
--
"Put down that coffee...coffee is for closers" |
|
Hilbe
join:2002-12-13
 ·AT&T U-Verse
 ·VoiceStick
| reply to rcilink
Anyone have a good dial plan? I can't seem to get my dial plan right...
--
Hilbe
»www.sunrocketforum.com
»www.nuvioforum.com |
|
happyvalley
join:2005-03-21
| reply to illek
I just followed the instruction. but didn't work for me. somebody can help. thanks
I run tftp server on my laptop. unzip two files to tftp server root. then disconnect the internet from the router
then connect the pap2 to the router.
from my laptop, I can access the pap2's page at 192.168.2.3
my laptop's address is 192.168.2.4. add user's password 1234
step 1-8, no problem.
on step 9.
before I upgrad the PAP2-SP2K.bin, the power led and network led are blue. after upgrad it, the power led flashes for about 10 second, then back to blue again. never turn red.
11. still ask for password for admin.
I am running tftp server download from here. I doubt the fireware is not updated. how can I check if my tftp server is running OK.
thanks |
|
Hilbe
join:2002-12-13 | reply to rcilink
I think the files need a "-" in them. |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
| reply to rcilink
you guys are right.. I goofed! The file names should have the "-" in them.. Just rename them to have the "-" (hyphen) in the names...
change PAP2SP2K.bin to PAP2-SP2K.bin
and
change SP2KPAP2.bin to SP2K-PAP2.bin
sorry about that!! |
|
hedwigdaowl
join:2005-03-20
Bloomfield, NJ | WOOT!! I unlocked the baby.
Now I can't get to setup stanaphone for this. I am setting this up behind a router. And I think I am doing something wrong with port forwarding or something. Any help or pointers appreciated.
Anyway thanks OP! |
|
happyvalley
join:2005-03-21 | download a tftp client here, make sure that the network communication works
»www.tftp-server.com/tftp-download.html
tftp 192.168.2.4 get PAP2-SP2K.bin
change the ip |
|
thankyouall
| reply to rcilink
where to input these data to setup a stanaphone account?thanks.
Username
Password
Domain/Realm
SIP Proxy
Outbound Proxy
DTMF
Other parameters |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
| reply to rcilink
Re: [PAP2] Configuring your PAP2 device
my suggestion for configuration questions...
go to voxilla.com and use their configuration tool.
for the PAP2 device, try this link: »voxilla.com/pap2config.php
(If it barfs, make sure you LOGIN to voxilla first..)
Their config form supports PAP2 settings for:
AdvanceCall
Bankoi
BroadVoice
DialPad
Free World Dialup
Go2Call
Gossiptel
iConnectHere
inPhonex
INX Logical Exchange
Musimi
Mutualphone
Net2Phone
Nikkom
Nikotel
SimpleTelecom
Sipgate.de
Sipgate.co.uk
SIPphone
StanaPhone
Telefin
Terracall
TrueVoIP
VoiceEclipse
VoicePulse (Connect or Open Access)
VoIPTalk (TelAppliant)
VoIP User (voipuser.org)
Vonage Softphone Account
Voxee
WorldDialPoint (Australia) |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to hardly
Re: [PAP2] Unlocking Guide
said by hardly  :Once unlocked, can you flash with Linksys PAP-2NA firmware? PAP2 and PAP2-NA firmware are 100% identical.
If so, can you then perform a Factory Reset without worrying about it reverting to Vonage defaults?
Thanks Once unlocked and factory reset, the PAP2 will be locked again. |
|
RXWatcher
join:2002-05-29
Riverside, RI
| reply to rcilink
Ok, unlocked my 2 units. I decided to try the latest sipura 2000 firmware (3.15) and it took except it caused the red power light and disabled line 2. I was thinking of trying the Sipura 2002 firmware. Has anyone tried it? I want to go with the Sipura firmware since they actually release it regularly  |
|
hardly
join:2004-02-10
USA
| reply to rizzo2dial
Is there a modified Sipura firmware available that will load using the PAP2 web interface from a file located on a local machine?
Would that effectively turn this device into a SPA2000 (or SPA2002), then only needing to update firmware as if it were a Sipura and not dealing with it reverting to a locked Vonage device?
PM me if you need to.
Thanks
said by rizzo2dial :The PAP2 and PAP2-NA use identical firmware. The PAP2 has different NVRAM values burned into the device than the PAP2-NA which is why a Master Reset reverts the device back to a locked Vonage adapter. I tried numerous combinations of trying to reset the adapter (both while in "Sipura" mode and "Linksys" mode, switching back 'n forth between the firmware flavors). It "Sipura" mode, a master reset acted like all "default Sipura" settings were loaded; however, once switching back to "Linksys" firmware, it was a locked PAP2 Vonage adapter again. Rizzo |
|
O_R
| reply to rcilink
I am glad to confirm that Staples-PAP2 is unlocked and I am able to receive incoming calls and also place calls!
Linksys PAP2 Configuration Wizard @ voxilla worked.
You can try stanaphone it is free and includes a NY phone #, but still in its beta phase.
thanks again for all contributors...
Good luck |
|
aomunoz
@200.72.x.x
|  reply to rcilink
Mr. rcilink
I don't have words to thank you.
I have been working a lot of time trying different methods to get my Linksys Vonage unlocked but all of that effort never gave me positive results, until your guide.
Excellent work, well done, very good job.
Thanks once again and for all, now I have a Sipura 2k working in my little box and administrator privileges what I was looking for a long long time...
Regards,
aomunoz@chile |
|
