cgigate
join:2003-05-12
Fort Worth, TX
4 edits | reply to vvonky
Re: [BPA410] stuck.. no response to anything!
said by vvonky  :For all that this is worth: I kept playing around, and eventually found a combination (which I don't remember) which reset it all back to "normal", and I can now enter the web interface again.... Could you figure out the combination to make the BPA410 to gain web interface access again....?
|
|
Mike_27
Premium
join:2004-05-15
Gardiner, MT | reply to rcilink
Re: [DTA310] Firmware - virtual office (MGCP)
cool  , i;ll give it a shot this weekend and report back.
Mike_27 |
|
cgigate
join:2003-05-12
Fort Worth, TX
1 edit | reply to rcilink
Re: [DTA310] Add a Serial Port to your DTA310
said by rcilink :Here's a glimpse into the RCI labs and the project that is currently being tested. I thought I had all the parts-- just to find out that I dont! Anyhow, here is a PDF showing the process we will perform to add a serial port to the DTA310 device. I tested the circuit diagram for serial port. it is not working as serial port |
|
hwittenb
join:2003-12-20
 ·Future Nine Corpor..
·callwithus
·Callcentric
| reply to rcilink
Re: [DTA310] Firmware - virtual office (MGCP)
said by rcilink :Here is the MGCP firmware for a DTA310. The hope was that this firmware would bring in the 8x8 download firmware (8x8 010208) that was reported to allow you to install the Leadtek AR18D firmware in the DTA. I tried it and it did not work for me.
At the end, I had 8x8 010222 downloader code. When I tried to install the Leadtek AR18D firmware, the application would not load. I was able, though, to reload my Leadtek AR17I firmware and the DTA is still useful.
When I first tried to install the DTA P8VO-116 firmware, the download said it was successful but when starting the application it did not come up but seemed "stuck". I had made the mistake of being connected to the internet and I realized that the unit was sending packets. My sniffer said they were to vo.packet8.net. I was able to reset the unit with the reset button, the phone off hook, and plugging in the power. It was at that point I tried to load the AR18D firmware. It said the download was successful but the application would not start. |
|
cgigate
join:2003-05-12
Fort Worth, TX
4 edits | reply to rcilink
Re: [DTA310] Firmware Recovery Thread
It was fun to play around with DTA310.
I have a DTA-310, I was lucky flashed it to AR18d .
I played it again to load MGCP version. it was OK to load MGCP, but the downloader code became 010222, MGCP nothing to play. I tried to go back with SIP, but accidentally loaded AR16O firmware from MGCP version , the downloader mode cannot reboot any more. I stuck in AR16O firmware, no way to downgrade and upgrade! a working unit with AR16O firmware only! |
|
cgigate
join:2003-05-12
Fort Worth, TX
| reply to rcilink
Re: [DTA310] Add a Serial Port to your DTA310
said by rcilink :I spoke with him. He said he does not remember where he got that 'info' he posted from (it was 14 months old). He also told me he does not have the software.  rcilink,
Have you got any information about T2burn software, or any progress for project ? |
|
zues
join:2005-11-03
The Dalles, OR
| reply to cgigate
Re: [BPA410] stuck.. no response to anything!
If you goto the leadtek website, they do have phone commands that can be implemented to set a static ip address on the adapter. But as far as I can tell it is ineffective on a bricked bpa due to incorrect firmware being loaded. All i get is the power light and the line1 light lit. |
|
New
@cox.net
| reply to rcilink
Re: [DTA310] Firmware Recovery Thread
Hello!
Somebody may help, I try install a new firmware in my BPA410 and its not finish, and now the BPA410 not link the network it work turn on the light power and line 1 but is not posible access the web configuration.
I was think maybe the firmware is uncompleted and not work the dhcp or something about auto DNS
Please help me! |
|
hwittenb
join:2003-12-20
·Future Nine Corpor..
·callwithus
·Callcentric
| said by New :
now the BPA410 not link the network it work turn on the light power and line 1 but is not posible access the web configuration. You can try and reset the BPA410 to some default
1. Unplug the power
2. Connect the telephone to the Line 1 port
3. Lift the handset off the hook (off hook)
4. Use a pin or something like it to push the reset button while you plug in the power. The power led should be flashing.
5. Continue to hold the led until you see 4 of the 6 led's flashing several times in pairs. Release the pin pushing the reset button and wait until all the led's stop flashing. This could take 10-seconds or so. Put the phone back on the handset.
As rcilink has posted, you should only try to download firmware meant for the Leadtek BVA8052 to the BPA-410. |
|
