Reviews:
 ·Suddenlink
| Need LP orifices for a GE cooktop, model JGP326WEV3WW So I need to convert this cooktop, a GE model JGP326WEV3WW, from natural gas to propane. The owners manual says that it shipped setup for nat gas, but that a set of propane orifices for the burners were also included with the "literature kit". It's an old cooktop and the orifices are long gone as far as I can tell.  Surely there are literally millions of these kits laying in the back of appliance installers trucks, but I just need to find one set. Are these fairly easy to find? The manual doesn't even state the sizes, so I'm not sure how or where to start looking. Does anyone out there have any ideas?
Thanks! |
|
 nunyaWho is John Galt?Premium,MVM
join:2000-12-23
O Fallon, MO
kudos:8 | »www.repairclinic.com/PartDetail/···26WEV3WW
--
...because I care. |
|
| You rock! I was searching for a kit. Didn't think about looking for individual parts. Must be time to get some sleep... 
Thanks! |
|
|
|
 tp0dyabbazooiePremium
join:2001-02-13
Carnegie, PA
kudos:4 | does the manual mention anything about changing the setting on the gas pressure regulator? some dual fuel appliances have 2 settings, one for nat, one for lp
-j
--
if it aint broke, tweak it!!
currently on FiOS (kick aZZ!) |
|
 shdesignsPowered By Infinite Improbabilty DrivePremium
join:2000-12-01
Stone Mountain, GA | reply to HarryH3
That site lists three orifices for LP.
The one linked before and a small and medium LP orifice.
Could be you need the right one for each size burner.
--
Scott Henion
Embedded Systems Consultant,
SHDesigns home - DIY Welder |
|
 SwedishRiderRider on the StormPremium
join:2006-01-11
Connecticut
kudos:1 | reply to HarryH3
I've had a number of appliances converted from nat gas to propane and I ALWAYS pay the propane company to do the conversion. I know that isn't very DIY, but propane and electrical are two things I don't fully understand and hence, pay the pros rather than chance a serious mistake.
If in doubt, call in the propane company. |
|
scooper
join:2000-07-11
Youngsville, NC
kudos:2 Reviews:
·Time Warner Cable
 ·Embarq Now Centu..
| said by SwedishRider:I've had a number of appliances converted from nat gas to propane and I ALWAYS pay the propane company to do the conversion. I know that isn't very DIY, but propane and electrical are two things I don't fully understand and hence, pay the pros rather than chance a serious mistake.
If in doubt, call in the propane company.
Sound advice - if you're not sure what you're doing, have someone that does take care of it. |
|
compPremium
join:2001-08-16
Cranberry Twp, PA | It is not rocket science. I was an appliance repair apprentice when i was 18 and did hundreds of these. takes 10-15 min max to changes out the orifices. Just read the instructions |
|
SwedishRiderRider on the StormPremium
join:2006-01-11
Connecticut
kudos:1 | said by comp:It is not rocket science. I was an appliance repair apprentice when i was 18 and did hundreds of these. takes 10-15 min max to changes out the orifices. Just read the instructions
For less than 100 bucks I had both my dryer and oven converted from nat gas to propane. My understanding in CT is that appliance stores and techs cannot do the conversion... it must be done by the homeowner or a licensed propane company/installer.
It didn't look too difficult, I agree. But I'd still rather the pros do the work... in the unlikely event something goes wrong... I have my conversion receipts for the insurance company.  |
|
Reviews:
·Suddenlink
| reply to tp0d
Yep, I have to remove the cap on the regulator, pop out the spring retainer, reverse it and reinstall the cap. Looking at it, it appears to just change the pressure on the regulator diaphragm, thus changing the output pressure. Sure beats having to buy a new regulator.  |
|
Reviews:
·Suddenlink
| reply to shdesigns
Yep, the manual shows that one of them (for the "Precise Simmer" burner) is different than the other three. After poking around a bit, I found »www.geapplianceparts.com which only lists medium (part WB28K145) and small (part WB28K5087) orifices for this unit. So 3 mediums and one small should have me cooking with gas.  |
|
Reviews:
·Suddenlink
| reply to SwedishRider
Like comp said, it ain't rocket science. I do gas and electrical quite often. Once you learn how to do it, it's pretty neat to do it yourself and know that it's done right. A couple of tools and a bottle of leak testing liquid is all it takes. A healthy dose of respect for the stuff you're working with also helps.
BTW, here's a great video of what can happen when you let the propane pros handle it: »www.youtube.com/watch?v=JzdnUZReoLM |
|
SwedishRiderRider on the StormPremium
join:2006-01-11
Connecticut
kudos:1
1 edit | I won't argue that there are some undertrained/careless propane techs and electricians that can cause tremendous damage and harm (and that applies to almost any trade). But I will argue that a vast majority of DIYers do not have the technical training, knowledge or proper tools to perform propane or electrical tasks safely.
If someone feels knowledgeable enough, has the right tools, pulls the proper permits, does the work, and then has it properly inspected, then so be it.
But weekend warrior non-permitted work (or an inexperienced homeowner "taking a stab at it") is far more dangerous IMHO than calling in a licensed propane company or licensed, experienced electrician.
As always... that's just my perspective..
But best of luck on your conversion project. |
|
