 DrStrangeTechnically feasiblePremium
join:2001-07-23
West Hartford, CT
kudos:1
3 edits | reply to Doctor Olds
Re: Upload almost non-existant. 5.21Mbps Down with 0.03Mbps Up There's nothing on the netstatus page [not that they'd bother to put anything there anyway], but you probably already know that.
Hopefully there's scheduled or unscheduled maintenance going on, they haven't done the final testing, and they'll figure out there's a problem when they check it.
Otherwise you'll have to rattle Support's cage and see if they can rip/rebuild [if I were a Covad tech with access to the right controls, that'd be what I'd do at this point; you've power-cycled and done all of the other Tier-One Support things and the line looks OK*].
*Stats not complete, see below.
One last question, though: What does your upstream noise figure look like? I only see the one for downstream. If you had some sort of RFI in the LF/lower MF range, it could theoretically affect your upload without affecting your download very much [except for saturated upload choking off the download eventually if it got bad enough]. |
|
 Doctor OldsI Need A Remedy For What's Ailing Me.Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
1 edit | I'd have to swap out the Modem. The Siemens/Efficient 4200 Router/Modem doesn't show upstream data except sync rate.
SpeedStream Telnet Server
login: username
password:
User logged in
xsh> show dsl stat
--- DSL Status
DSL State - Up
Tx Rx
CRC Errors 1 29
FEC Errors 0 0
HEC Errors 68 0
NCD Errors 0 0
LCD Errors 0 0
LOF Errors - 0
LOS Errors - 0
--- ATU-R Channel Info
Current Tx Rate - 768000
Previous Tx Rate - 0
Interleave Delay - 2489120176
--- ATU-C Channel Info
Current Tx Rate - 6016000
Previous Tx Rate - 0
Interleave Delay - 2
--- ATU-R Physical Layer Info
Current Attainable Rate - 6016000
Current SNR Margin - 11.5
Current Attenuation - 32.5
Current Output Power - 6.0
Current Status:
No defects detected
No loss of framing detected
No loss of signal detected
No loss of power detected
No loss of signal quality detected
--- ATU-R Line Status
Line Coding - DMT
Line Type - Interleaved
Actual ADSL Mode - G.dmt
Requested ADSL Mode - Auto
xsh>
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
|
|
Doctor OldsI Need A Remedy For What's Ailing Me.Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18 | reply to DrStrange
»netspeed.stanford.edu/
TCP/Web100 Network Diagnostic Tool v5.5.4a
click START to begin
** Starting test 1 of 1 **
Connected to: netspeed.stanford.edu -- Using IPv4 address
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 15.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . 3.00Mb/s
Your PC is connected to a Cable/DSL modem
click START to re-test
** Starting test 1 of 1 **
Connected to: netspeed.stanford.edu -- Using IPv4 address
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 57.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . 3.45Mb/s
Your PC is connected to a Cable/DSL modem
click START to re-test
»jlab4.jlab.org:7123/
TCP/Web100 Network Diagnostic Tool v5.5.4a
click START to begin
** Starting test 1 of 1 **
Connected to: jlab4.jlab.org -- Using IPv4 address
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 18.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . 4.96Mb/s
Your PC is connected to a Cable/DSL modem
[S2C]: Packet queuing detected
click START to re-test
** Starting test 1 of 1 **
Connected to: jlab4.jlab.org -- Using IPv4 address
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 18.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . Server Failed while receiving data
S2C throughput test FAILED!
Protocol error!
click START to re-test
»speedtest.umflint.edu/
TCP/Web100 Network Diagnostic Tool v5.5.4
click START to begin
** Starting test 1 of 1 **
Connected to: speedtest.umflint.edu -- Using IPv4 address
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 14.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . 4.72Mb/s
Your PC is connected to a Cable/DSL modem
[S2C]: Packet queuing detected
click START to re-test
** Starting test 1 of 1 **
Connected to: speedtest.umflint.edu -- Using IPv4 address
Another client is currently being served, your test will begin within 45 seconds
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
checking for firewalls . . . . . . . . . . . . . . . . . . . Done
running 10s outbound test (client-to-server [C2S]) . . . . . 88.0kb/s
running 10s inbound test (server-to-client [S2C]) . . . . . . 4.98Mb/s
Your PC is connected to a Cable/DSL modem
[S2C]: Packet queuing detected
click START to re-test
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
