What do these sh dsl int atm0/0 - atm0/1 mean ??

Author	All Replies
elegua join:2006-08-30	What do these sh dsl int atm0/0 - atm0/1 mean ?? Hi Guys, I got a call from my ISP today that my Dual DSL lines was configured, after configured my router i noticed a lot of errors and low connectivity to internet, these are my sh dsl int atm0/0 and 0/1: Router#sh dsl int atm0/0 ATM0/0 Alcatel 20150 chipset information ATU-R (DS) ATU-C (US) Modem Status: Down (DMTDSL_SHOWTIME) DSL Mode: ITU G.992.1 (G.DMT) Annex A ITU STD NUM: 0x01 0x1 Vendor ID: 'ALCB' 'GSPN' Vendor Specific: 0x0000 0x0008 Vendor Country: 0x00 0xFF Capacity Used: 82% 104% Noise Margin: 11.0 dB 7.0 dB Output Power: 8.0 dBm 9.5 dBm Attenuation: 13.5 dB 9.5 dB Defect Status: None None Last Fail Code: Error in early non-CRC message or in first CRC-covered message Selftest Result: 0x00 Subfunction: 0x15 Interrupts: 1338 (0 spurious) PHY Access Err: 0 Activations: 1 LED Status: ON LED On Time: 100 LED Off Time: 100 Init FW: embedded Operation FW: embedded SW Version: 3.8131 FW Version: 0x1A04 Interleave Fast Interleave Fast Speed (kbps): 0 6016 0 608 Cells: 0 0 0 34177 Reed-Solomon EC: 0 0 0 0 CRC Errors: 0 5 0 1126 Header Errors: 0 5 0 620 Bit Errors: 0 0 BER Valid sec: 0 0 BER Invalid sec: 0 0 LOM Monitoring : Disabled DMT Bits Per Bin 00: 0 0 0 0 0 0 0 7 7 0 8 9 A A A A 10: 9 0 9 A A A A 9 8 0 7 7 7 7 0 0 20: 0 0 0 0 0 0 2 2 3 4 5 5 6 6 6 7 30: 7 7 7 7 7 8 8 8 8 8 8 7 2 7 6 6 40: 0 6 7 8 8 9 9 A A A A A A B B B 50: B B B B B B B B B B B B B B B B 60: B B B B B B B B B B B B B A A B 70: A A A A A A A A A A A A A A A A 80: A A A A 9 9 9 8 6 2 7 8 8 8 8 8 90: 8 7 6 5 2 3 5 6 7 7 7 6 5 3 2 4 A0: 6 7 7 8 8 8 8 8 8 8 8 7 6 8 9 8 B0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8 9 C0: 9 9 9 9 9 8 9 9 9 9 9 9 8 9 9 9 D0: 8 8 8 8 7 7 8 7 7 7 7 7 7 7 7 6 E0: 6 6 5 5 5 5 5 5 4 3 0 2 3 4 4 4 F0: 4 3 2 0 0 0 0 0 0 0 0 0 0 0 0 0 DSL: Training log buffer capability is not enabled Router#sh dsl int atm0/1 ATM0/1 Alcatel 20150 chipset information ATU-R (DS) ATU-C (US) Modem Status: Showtime (DMTDSL_SHOWTIME) DSL Mode: ITU G.992.1 (G.DMT) Annex A ITU STD NUM: 0x01 0x1 Vendor ID: 'ALCB' 'GSPN' Vendor Specific: 0x0000 0x0008 Vendor Country: 0x00 0xFF Capacity Used: 71% 104% Noise Margin: 14.5 dB 7.0 dB Output Power: 8.0 dBm 10.0 dBm Attenuation: 13.0 dB 25.0 dB Defect Status: None None Last Fail Code: Error in early non-CRC message or in first CRC-covered message Selftest Result: 0x00 Subfunction: 0x15 Interrupts: 2660 (0 spurious) PHY Access Err: 0 Activations: 2 LED Status: ON LED On Time: 100 LED Off Time: 100 Init FW: embedded Operation FW: embedded SW Version: 3.8131 FW Version: 0x1A04 Interleave Fast Interleave Fast Speed (kbps): 0 6016 0 736 Cells: 0 87316 0 1612772 Reed-Solomon EC: 0 0 2 1 CRC Errors: 0 610 2 24 Header Errors: 0 415 1 9 Bit Errors: 0 0 BER Valid sec: 0 0 BER Invalid sec: 0 0 LOM Monitoring : Disabled DMT Bits Per Bin 00: 0 0 0 0 0 0 0 8 9 9 9 9 A A A B 10: B B B B A A 7 9 8 5 7 7 8 8 0 0 20: 0 0 0 0 0 0 3 3 4 4 5 5 6 6 7 7 30: 7 8 8 8 9 9 9 9 9 9 9 A A A A A 40: 0 A A A A A 9 A A A A A A A A A 50: A A A A A A B B A B B B B 2 B B 60: B B B B B B B B B B B B A A A A 70: A A A A A A A A A A A 9 9 A 9 9 80: 9 9 9 9 9 9 9 8 6 3 7 8 9 8 8 8 90: 8 7 6 5 2 3 5 7 7 6 6 6 4 2 0 4 A0: 5 6 7 7 8 8 8 8 7 8 8 6 5 8 8 7 B0: 9 9 9 9 9 9 8 8 9 9 9 9 9 8 7 9 C0: 9 9 9 9 9 7 9 8 8 8 8 8 7 8 8 8 D0: 8 8 8 7 7 7 8 7 7 7 7 6 6 6 6 6 E0: 6 6 6 6 6 6 5 5 4 2 0 2 4 4 5 5 F0: 5 4 3 0 0 0 0 0 0 0 0 0 0 0 0 0 DSL: Training log buffer capability is not enabled Router# This is the MLPPP configuration in my router: interface ATM0/0 no ip address no atm ilmi-keepalive bundle-enable dsl operating-mode auto ! interface ATM0/0.1 point-to-point pvc 0/35 pppoe-client dial-pool-number 1 ! interface ATM0/1 no ip address no atm ilmi-keepalive bundle-enable dsl operating-mode auto ! interface ATM0/1.1 point-to-point pvc 0/35 pppoe-client dial-pool-number 1 ! interface Dialer0 ip address negotiated ip access-group WAN in ip mtu 1492 ip nat outside ip inspect FIREWALL out ip virtual-reassembly encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname XXXXXXXXXXXX ppp chap password XXXXXXXXXXXX ppp multilink ppp multilink links minimum 2 My current speed: If you guys need more info just let me know, i have new phone cables running at home, also the box in less that 6 feet from the router, my phone has filter. Thanks in advance. ;) ;)
	to forum · permalink · · 2008-06-13 22:35:50 ·
rolande Certifiable Premium,Mod join:2002-05-24 Powell, OH clubs: Host: Linksys AT&T Midwest	I assume the provider is provisioned to support MLPPP on their end too? The health of the DSL signal appears okay for both lines based on the synch speeds. However, you do have a few CRC's and header errors occuring on the second interface just greater than 1% combined. That is significant enough to cause slowdowns and TCP retransmissions. What provider is it? -- Scott, CCIE #14618 Routing & Switching Ignorance is temporary...stupidity lasts forever! »www.thewaystation.com/techref/tech.shtml »blog.thewaystation.com/
	to forum · permalink · · 2008-06-13 23:59:40 ·
elegua join:2006-08-30	Hi, Thanks for answer me. Yes, my ISp supports MLPPP, sorry but do you mean with "What provider is it?" ??.
	to forum · permalink · · 2008-06-14 00:30:46 ·
rolande Certifiable Premium,Mod join:2002-05-24 Powell, OH clubs:	Which ISP are you using and what part of the country is this in? Do you know how far you are from the CO or Remote Terminal? Also is this a newer are with newer telco cabling or has it been around for along time?
	to forum · permalink · · 2008-06-14 12:14:21 ·
Chewbakka join:2004-12-19	I just want to hijack this thread really quick... Regarding ATM interfaces, is it safe to fiddle around with the fr-vbr, fr-cbr options, or should you leave those alone?
	to forum · permalink · · 2008-06-15 15:15:52 ·
elegua join:2006-08-30	reply to rolande Hi rolande, I'm in Canada, i'm less than 5Km to the CO also they have been in this bussines for quite a bit. Thanks.
	to forum · permalink · · 2008-06-15 16:06:55 ·
ciscoiphead join:2007-07-03 Ashland, VA	reply to Chewbakka said by Chewbakka : I just want to hijack this thread really quick... Regarding ATM interfaces, is it safe to fiddle around with the fr-vbr, fr-cbr options, or should you leave those alone? VBR is probably the best choice, tx-ring-limit is also good practice to have. Example: interface ATM0/0/0 no ip address load-interval 30 no atm ilmi-keepalive dsl operating-mode itu-dmt dsl enable-training-log pvc 0/35 vbr-nrt 448 448 1 tx-ring-limit 3 encapsulation aal5snap service-policy output V3PN pppoe-client dial-pool-number 1 #sh queueing interface atM 0/0/0 Interface ATM0/0/0 VC 0/35 Queueing strategy: weighted fair Output queue: 0/512/64/647 (size/max total/threshold/drops) Conversations 0/31/32 (active/max active/max total) Reserved Conversations 2/2 (allocated/max allocated) Available Bandwidth 22 kilobits/sec
	to forum · permalink · · 2008-06-16 08:07:04 ·


Saturday, 06-Sep 13:52:10	Terms of Use \| Privacy Policy \| Hosting by www.nac.net - DSL,Hosting & Co-lo \| feedback \| contact over 9 years online! © 1999-2008 dslreports.com.republican-creole page compression OFF