|Home||Reviews||Tools||Forums||FAQs||Find Service||ISP News||Maps||About|
how-to block ads
Instrutions for accessing the modem configuration where you can change the VPI/VCI setting.
This will reset the modem back to factory defaults, and may recover your modem after you have made a mistake in changing some of the settings and don't know how to change them back.
not work Reset button
HERE. (Please note that the Alcatool software is not an Alcatel product, and use of it is at your own risk. Alcatool will NOT work with Speedtouch USB modems.)
If you have a router, temporarily bypass it for this test. Configure your computer to use the local IP address 10.0.0.2, subnet mask 255.255.255.0 with no gateway or DNS. Restart your computer to force the change to take effect. Then start Alcatool, enter the address 10.0.0.138 with no password and click connect. Press the "Line Stats" button the lower right corner then select "Line Info".
METHOD 2: Refer to this FAQ item
Both methods will yield the same result.
Attainable line rate : 7516 kbit/sec Maximum theoretical download rate
Attainable Atm rate : 7040 kbit/sec Maximum actual download rate before TCP overhead
Used line rate : 3400 kbit/sec Current theoretical download rate
Fast used Atm rate : 3008 kbit/sec Current actual fastpath download rate before TCP overhead. If this number is zero, please see the next line.
Interleaved used Atm rate : 0 kbits/sec Current actual interleaved download rate before TCP overhead. If you see a number other than zero here, your line is interleaved.
Rel. capacity occupation : 45 Percentage of line capacity used. If this number is above 78%, your line in its current state does not qualify for any speed upgrades.
Noise Margin : 17 dB This is a measure of how good your data signal is relative to the noise on the line. This should be a high number and in any case no lower than around 6 dB. If it's this low you could find the modem gets data errors or even sync problems.
Line attenuation : 42 dB Measures how much signal loss there is on the line - this should be a low number and in any case should be no more than around 60-65 dB.
Output Power : 15 dBm Indicates how hard the modem is working to maintain the link. High numbers (around 19 or above) can indicate possible problems.
Explanations for upstream data is the same as above.
Any of these numbers near or at the limits described can cause the modem to lose sync and/or have high error rates resulting in poor internet performance. This is usually due to poor cabling, interference, or a line which is near or at the distance limit of where ISP can still provide ADSL from the DSLAM.
Not all modem versions support displaying of upstream stats.
2. Start a DOS prompt or Command prompt.
3. Type telnet 10.0.0.138
4. Once you are logged in, issue the following command: adsl info
Channel Mode - If this line says "Fast", you are on fastpath. Otherwise your line is interleaved.
Margin - This is a measure (in dB) of how good your data signal is. Higher numbers are better. If this number drops below 6, you'll start to have sync problems.
Attenuation - Measures (in dB) how much signal loss there is on the line - this should be a low number and in any case should be no more than around 60-65 dB.
Available Bandwidth - Current sync rate in kilobits per second. This is NOT your maximum attainable sync rate.
In the above sample results, the line potential is not revealed to the end user. However, we can examine the SNR Margin and Attenuation numbers. In this case, the downstream and upstream margins are 25 and 31, which are much greater than the minimum of 6. The downstream and upstream attenuation is 26 and 15, which are much lower than the maximum of 60-65. Therefore, this line would likely qualify for a speed upgrade. How much of an increase is possible cannot be known from this data, but these numbers are good indicators.
2) I find that DHCP does not work on a "new" internal IP address, e.g. adding 172.17.0.1 unless I first delete 10.0.0.138 before setting up the address pool. I.e. Add IP - Add Pool - Delete 10.0.0.138 never lets the DHCP work, whereas Add IP - Delete 10.0.0.138 - Add Pool does.
This applies to firmware 22.214.171.124
1. Telnet to the Speedtouch: telnet 10.0.0.138
2. Login (the default username is: Administrator) with no password
3. Enter the following commands (one line at a time):
service system ifadd name=PING_RESPONDER group=wan
got feedback?here for instructions.
The first is the username and password used to protect the modem's web interface from unauthorized users. There isn't a default username and password set, so if one has been set, it's been done by you, somebody else, or the ISP who owns the modem. See here for password reset instructions.
The second is the EXPERT password, used for configuring advanced functions not available through the web interface. The EXPERT password is derived from the MAC address, and can be found by using this webpage. The EXPERT password is entered when accessing the modem's telnet command line interface.